Free DIY calculator

Paver base calculator: how much gravel base and sand under pavers?

Quick answer: A 10 by 12 foot patio with a 4 inch gravel base needs about 2 tons of crushed stone and half a ton of bedding sand. The base goes down 4 inches deep for foot traffic and 6 inches for a driveway, with 1 inch of sand on top of the stone. Enter your length, width and base depth below and the calculator gives you the cubic yards and tons for both layers.

Pavers sit on two layers, not one: a compacted gravel base that carries the load, and a thin layer of bedding sand the pavers are set into. A 10 by 12 foot patio with a 4 inch base needs 1.63 cubic yards of crushed stone, about 2.28 tons, plus 0.41 cubic yards of sand, about 0.55 tons. Work out both layers below before you call the stone yard, so you order the base and the sand in one delivery.

Last updated: November 17, 2026.

Estimate only — check your supplier's current price and local code before ordering.

Tired of chasing manually? Let Invoice Chaser run the day 7, 14 and 30 reminder sequence automatically — free for up to 3 invoices.

Start chasing automatically — free

How do you calculate paver base and bedding sand?

Two layers, the same volume maths for each:

Base depth is the decision that moves the numbers most. The industry minimum is 4 inches of compacted base for patios and walkways and 6 inches for residential driveways over well-drained soil, with a nominal 1 inch of bedding sand on top. Weak, wet or freezing ground needs a thicker base — the extra stone is cheaper than relaying sunken pavers.

How much base and sand does a 10 by 12 foot patio need?

A 10 by 12 ft patio, 4 in of gravel base, 1 in of bedding sand, with a 10% waste allowance:

So order about 2.3 tons of crushed stone and just over half a ton of sand for this patio. Run the same patio as a driveway at a 6 inch base and the gravel alone jumps to 3.42 tons — the depth, not the size, is what catches most people out.

How much base and sand do common patios and driveways need?

ProjectGravel base (cu yd)Gravel base (tons)Bedding sand (cu yd)Bedding sand (tons)Total (tons)
10×10 ft patio, 4 in base1.361.90.340.462.36
10×12 ft patio, 4 in base1.632.280.410.552.83
12×20 ft driveway, 6 in base4.896.840.811.17.94
20×20 ft patio, 4 in base5.437.611.361.839.44

All rows: 1 in of bedding sand and a 10% waste allowance on both layers. The driveway row is the only one at a 6 inch base — that extra 2 inches adds roughly half as much gravel again for the same area. Change any of them in the calculator above for your exact project.

What should you check before you order paver base?

First, confirm how your supplier sells: by the cubic yard or by the ton, and which density they use. This calculator uses 1.4 tons per cubic yard for crushed stone and 1.35 for dry sand, which are the standard planning figures — but a supplier weighing wet stone or a different rock type will quote a different tonnage for the same volume, so use their figure for the final order.

Second, order both layers in one delivery where you can. The worked example above is 2.83 tons in total, and a second small delivery costs nearly as much to send as the first. Third, check the excavation: a patio needs the base depth plus 1 inch of sand plus the paver thickness dug out, so a 4 inch base with 1 inch of sand and 2 and 3 eighth inch pavers means digging about 7 and a half inches below the finished height.

That figure covers the base material only. It does not include the pavers themselves, edge restraints, landscape fabric, a plate compactor hire, or labour — and it does not include a permit, which most towns do not require for a patio but some neighbourhood associations restrict.

Embed this calculator on your site

Copy the code below and paste it into any page to embed this calculator.

What do people ask before laying pavers?

How deep should the gravel base be under pavers?

For a patio or walkway, use at least 4 inches of compacted crushed stone, and for a residential driveway use at least 6 inches. Those are the minimum depths in the Concrete Masonry and Hardscapes Association guidance for well-drained soil. Weak, wet or freezing ground needs a thicker base, so check local conditions before you dig.

How much gravel base do I need for a 10 by 10 patio?

A 10 by 10 foot patio with a 4 inch base needs about 1.36 cubic yards of crushed stone, or about 1.9 tons, once a 10 percent waste allowance is included. The same patio also needs about 0.34 cubic yards of bedding sand, or about 0.46 tons. A deeper base raises both figures fast.

What kind of sand goes under pavers?

Use coarse, angular concrete sand that meets ASTM C33, screeded to 1 inch and never more than 1.5 inches. Do not use play sand, mason sand or stone dust for bedding, because fine grains shift under load and hold water. Level the compacted gravel base first, since a thick sand layer cannot fix a low spot and will rut.

Should I add extra material for compaction and waste?

Yes, add 10 percent to both the gravel base and the bedding sand. Loose stone and sand pack down when compacted, and no patio is level, so the exact volume always falls short. Ordering the extra material in the first load is cheaper than paying for a second delivery, and leftover stone is useful for repairs.

Where do the numbers come from?

What other DIY calculators are there?

See all of them on the DIY material calculators page — one new calculator every day.

More free calculators and generators: Fence calculator · Concrete slab calculator · Mulch calculator · Gravel driveway calculator · Tax set-aside calculator · Freelance rate calculator · Paint calculator · Tile calculator · Freelance platform fee calculator · Project quote calculator · Drywall calculator · Laminate flooring calculator · Concrete block calculator · Deck stain calculator · Hourly-to-salary converter · Fence stain calculator · Concrete mix calculator · Retainer rate calculator · Roofing shingle calculator · Siding calculator · Driveway sealer calculator · Insulation calculator · 1099 vs W-2 calculator · 1099 quarterly tax calculator · Brick calculator · Lumber calculator · Stair calculator · Freelance contract generator · Receipt maker · Late payment demand letter generator · Freelance NDA generator · Asphalt calculator · Wallpaper calculator · Freelance proposal generator · Vinyl plank flooring calculator · Gutter calculator · Freelance scope of work generator · Carpet calculator · Retaining wall calculator · Freelance timesheet calculator · Bulk gravel calculator · Sand calculator · Paver base calculator · Home office deduction calculator · Freelance mileage calculator · Solo 401(k) contribution calculator · Freelance quote generator · Freelance tax deductions calculator · Freelance platform comparison calculator · DIY checklist generator · Freelance rate by profession calculator · How to chase a late payment guide · Free invoice template library by trade · DIY project cost guides · How to write an invoice guide · Late fees in Virginia guide · Late fees in New Jersey guide · Late fees in Oregon guide · Late fees in the District of Columbia guide · Late fees in Mississippi guide · Late fees in Montana guide · Late fees in Nebraska guide · Late fees in Oklahoma guide · All DIY calculators